Current Interruption Test Set 3000A

• Customization: Available
• Max Diameter of Workpiece: L
• Mass Scope of Workpiece: Light
• Model NO.: DDG-3000A
• Maxcapacity: L
• Load Way: Mechanical Load
• Loading Method: Dynamic Load
• Display: Digital
• Control: Manual Control
• Weight: 0-100Kg
• Power Source: AC220V
• Oil Cylinder Position: L
• Primary Current Injection: Primary Current Injection 2000A
• Transport Package: Plywood Case Outside
• Specification: CE
• Trademark: GOLDSOL
• Origin: China
• HS Code: 903033200
• Production Capacity: 20sets/Month
• Package Size: 45.00cm * 45.00cm * 70.00cm
• Package Gross Weight: 140.000kg

Product Description

I. Introduction
Strong current generator is the necessary equipment in places of strong current. It is widely used in power plants, power distribution stations, electrical manufacturers, research institutes and other departments. The equipment has the characters of short-term or intermittent system, small size, light weight and easy maintenance and so on.

II. Structure
The product has full metal shell and aluminum-alloy panel combination with  reasonable structure, elegant appearance, light weight and easy move.


1: Start  Button      2: Stop Button    3: Current Regulation Handle
4: Current Switch  5: Strong Current Indicator 6: Power Indicator
7: Weak Current Indicator 8: Voltage Switch 9: Operation Indicator
10: Voltage indicator   11: Strong Current Output   12 & 13:Power Input


III. Instructions

1.Connect the current amplifier with the tested product according to the testing requirements, and make sure that there's power supply. (For split type, connect the "input" on the panel with the power, the "output" with the "input" on DDK, and the "instrument" with the "instrument" on DDK.

2.Select the position of Current Switch according to the needed current.

3.Turn on the power, and the green light should be on (if not, turn the Voltage Switch counterclockwise to zero until the green light is on). Press the Startup Button, the green light should be off and the red light is on. Turn the Voltage Switch clockwise until the current rises to the needed level.

4.Turn the Voltage Switch counterclockwise to zero, press the Stop Button, the red light is off and the green light is on. The testing is over.



IV. Electrical Diagram
1. Diagram of Current Generator
     
2.Output copper wires connection method at open-backed door: 

V. Maintenance Notes
1. when acceptance of goods, please check the main circuit terminal block if it is loose, or if elecrical brush of regulator is with a  good contact.

2. when not using for a long time, please check the main circuit of insulation earth resistance with 500V Megohmmeter before the equipment will be used, the resistance should be not less than 0.5 MΩ.

3. Input voltage value should be ± 10%, frequency 50HZ.

4. Current switch are not allowed to operate with load.

5. Operation should be equably & slowly rotating hand wheel to avoid damaging the regulator.

6. Full load hours should not exceed 5 minutes, continuous work time should be less than 2.5 minutes, but the working cycle should be more than 10 minutes.

7. Earth terminal should be well grounded.


VI. Technical Parameters and Specifications for DDG series (Single phase)
 

Model	Capacity of Current Amplifier (KVA)	Capacity of Voltage Regulator (KVA)	Supply Voltage (V)	No.of Phase		Remark
DDG-500A	3	2	220	1		1 unit
DDG-1000A	6	5	220	1		1 unit
DDG-1500A	9	10	220	1		1 unit
DDG-2000A	12	10	220 /380	1	2	1unit/2unit
DDG-2500A	15	10	380	1	2	1unit/2unit
DDG-3000A	18	15	380		2	1unit/2unit
DDG-4000A	24	20	380		2	2 unit
DDG-5000A	30	28	380		2	2 unit
DDG-6000A	36	30	380		2	2 unit
DDG-8000A	48	40	380		2	2 unit
DDG-10000A	60	50	380		2	2 unit
DDG-15000A	90	75	380		2	2 unit
DDG-20000A	120	100	380		2	2 unit

   VII. Accessories

Sr no	Description	Qty	Remarks
1	Power supply cable	1
2	Connection cables	1
3	Earth cable 6m	1
4	Operating manual	1
5	Factory's calibration	1
6	Strong current cables	2	For buyer's option